If your toilet flange is too high, it means that the distance between the top of the toilet base and the top of the sub-floor is too small to accommodate the toilet. If that’s the case, then you’ll need to raise the flange, to solve the problem. But before you go out and start tearing up your bathroom, you’ll want to make sure you have all the supplies you’ll need to complete the task.

So, you’re doing a renovation and you need to replace your flange. What’s a flange? A flange is the flange that attaches to the toilet bowl to support the seat, lid and tank. The flange should be located so that the top of the flange is flush with the finished floor when the seat is in the down position. The flange should not be placed higher than the finished floor. Are you ready for the challenge? Do you think you have what it takes? Then, it’s time to join the Blogger Challenge! Here’s how it works: 1. You, or someone of your choosing, starts a post on your blog about a challenge you’ve chosen. 2.

If you’re thinking about replacing your old toilet, or purchasing a new one for the first time, you may be surprised to find out that the flange on the toilet is different than those of older models.  The toilet flange is the base that the toilet sits on. Older toilets had the flange on the same level as the floor, but newer models have a higher flange that is set into the wall.

If your toilet flange is too high, your toilet may rock back and forth during use. You may also notice water leaking from the flange. Over time, fluctuations and leaks can cause the ground to collapse or deform. A leaking toilet flange can lead to floor rot and mold growth. When this problem occurs, several methods can be used to correct it. Read on to find out more.

What is a toilet flange and do you really need one?

Before we look at how to fix a high toilet flange, we first need to understand what it is. The toilet flange connects the toilet bowl to the septic tank pipe. This device is made of different materials, such as iron or PVC.  It is attached to the bathroom floor to prevent the toilet from leaking during use. The flange essentially acts as a funnel that directs wastewater to the sewer pipe and septic tank. In addition to its main task – draining water – the flange also serves to elevate the toilet bowl. If your toilet flange is too high, you can make some adjustments to lower this unit. Read more at ….

How to repair the toilet upper flange

Raising the floor of the bathroom

Raising the bathroom floor is an effective way to adjust the height of the toilet flange. Depending on the height you want to add, it’s best to pad the tiles underneath for proper support. To raise the floor, an extra layer of tiles is sufficient, or, for example, risers can be used. B. Plywood, to be installed prior to laying the tiles. This allows the toilet to be placed correctly on the bumper. You can also use cement slabs to raise the height of the toilet. In the following paragraphs, we will explain how to raise your bathroom floor using the ideas above:

Method 1: Plywood for floor extension

Step 1:You will need a circular saw for this task. Cut the plywood according to the amount you will use. Measure the area of the floor to be cut to the correct size. Step 2:Now measure the distance from the center of the toilet flange to the nearest wall. Draw this size on the first piece of plywood with a pencil. The next measurement should be the distance from the opposite wall to the toilet flange and its center. Record this measurement on a second piece of plywood. Step 3:After you have measured the distances, add a half inch and draw a circle with a compass or round head. The circle can then be cut out with a wood carver. Step 4:Now it’s time to mount each veneer on the toilet flange and make sure it fits properly. Secure the plywood with glue or screws. You are now ready to install the toilet.

Method 2: Cement slab

If the space between the bathroom floor and the outer circumference of the flange is minimal, it can be filled with a cement slab, on which tiles are laid. The advantage of using cement slabs is that swelling due to water leakage is impossible and it is a stable flange solution. Swelling can lead to cracks in your tiles and cost you money to replace them. You can avoid this inconvenience by raising your floor with a cement slab. Follow the steps below to learn how to do this: StepMeasure the ground where you want to raise the subfloor. This will determine how many pieces of cement board you will need. Step 2:Measure the radius of the flange to create a round shape on the back planks. You will need a pencil to draw a circle before making the hole. Step 3:Put 4 pieces of cement board together to form a larger square. Draw a circle in the center of the largest square and add a half inch to the measurement. Now cut out a circle and make sure the plate fits perfectly on the toilet flange. Step 4:Spread the cement evenly over the entire raised floor. Then lay the tiles while the cement is still wet. Secure the rear panels with corrosion resistant screws. Make sure cement is applied around the outer flange and between the screens. Step 5: Finally, to install the tiles on the subfloor, apply tile adhesive to the tiles, making sure the tiles cover the joints well. You can then screw the flange to the floor and continue with the installation of the toilet.

Use of mortar

Joint sealant is another excellent material to use when the toilet flange is too high. Follow the steps below to use this tool: Step 1: Start mixing the coulis. Follow package directions or put a small amount in a container and add water at a ratio of 6 mortars to 1 water. This will ensure that you have enough grout to get the job done. Step 2:Remove the toilet bowl and place it on the four rubber bumpers. The washers are used to prevent the toilet from moving around the flange during grouting. Step 3:Now take the mixed mortar and fill the space with it. Do it all around the perimeter of the toilet. Wait 24 hours for the grout to dry. Step 4:Once the grout is completely dry, remove the rubber seals. It can be difficult to get them out, but with a little effort they will come out. Step 5:After you have removed all joints, seal all areas where you have removed the joints. Step 6:Finally, tighten the screws on the bottom of the toilet bowl so that it is secure. Tip: While the grout is drying, you can speed up the drying process by spraying water on the grout. Use a spray bottle and add as much liquid as you can. This will make the mixture firmer when it hardens. Have you tried all the methods above and still not satisfied with the height of the bridle? Consider replacing the toilet bowl and flange to solve the problem.

Install new toilet and flange

If your toilet flange is still too high, the last option is to replace it. To do this, remove the toilet bowl, the old flange and the pipe fittings. When installing a new toilet and flange, the first and most important thing you need to do is determine the proper flange height. After removing the old toilet, measure the height of the flange from the top to the floor. The ideal height of the flange should be a quarter inch above the ground. This allows a wax ring to be installed to seal the flange. If your bathroom floor is newly tiled, the toilet flange is probably above the desired level. If the distance to the bathroom floor is not sufficient, add a flange extension. These tools are quick and easy to install and are usually offered in quarter or half-inch sizes. The flange extension is meant to make the flange higher, and most come with long bolts. When you buy a new toilet flange, make sure it seals properly to prevent leaks. Install the new flange by inserting it into the pipe, then drilling four holes in the bottom to secure the flange. Finally, mount the new toilet on the flange and tighten the screws to secure. How long does the toilet flange last? The toilet flange does not have a defined life span. If installed correctly, attached to the floor and perfectly aligned, it should last 25 years or more. If you notice water leaking from the bottom of the toilet bowl, the main culprit may not be the toilet flange. Check whether the wax ring has come loose. A wax ring should last up to 25 years, but can deteriorate over time. To replace the washer, remove the toilet bowl and install a new washer before replacing the bowl. What space do I need for the toilet flange? Since standard drywall is about one-half inch thick, the flange should be at least 15 inches from the center of the unit to the wall stud. The average distance from the back is 12.5 inches, so you have plenty of slack.

Supplement

A high toilet flange can cause water to leak and the toilet bowl to wobble during use. Back and forth swings and leaks can warp or destroy your bathroom floor over time. A leaking toilet flange can also lead to rot and mold in the basement. Repairing a high flange is not an expensive or complicated job. Using any of the methods described above, such as. B. Grouting or raising the subfloor should solve this problem. But if you don’t want to do the work yourself, it’s best to call a licensed plumber. The sooner you address this problem, the fewer repairs you will have to make, saving you money and hassle.Depending on your bathroom style, the toilet may be one of the most visible elements in a room. It is important to get the toilet flange level with the floor.. Read more about toilet flange 1/8 inch above floor and let us know what you think.

Frequently Asked Questions

What happens if toilet flange is too high?

Replacing a toilet? If your new toilet flange is too high to seal, or if there is space between the floor and the base of the toilet, you may need a flange extension kit or a flange reducer kit to fix the problem. The toilet flange is the metal ring that attaches to the floor and supports the toilet. Since the flange is metal, it is prone to rusting. If rusted, you may be able to pry it up from the floor and replace it with a new one. If it is not rusted, you can replace it with a flange extension kit or a flange reducer kit. You’ve built an addition onto your home or a new home, and now you need to install a new toilet. You’ve carefully measured and made sure that the new toilet will fit in your bathroom. But wait – when you install the new toilet, it won’t fit. The toilet flange is too high.

How do I lower the toilet flange?

Whether you are a homeowner trying to fix your old toilet or a professional plumber trying to fix a major leak, raising and lowering the toilet flange is a skill you will need to know. If the flange is too high, you will have a hard time keeping the water in the bowl. If the flange is too low, you will have a hard time keeping the water from leaking out onto the floor. So you’re ready to remodel your bathroom. Good for you! In the process of designing your dream bathroom, you find that you’re not satisfied with the height of your toilet flange. And if you’re going to do one custom job right, you might as well go all in, right? If you’ve already adjusted the hinges and still can’t get the toilet flange at a level you’re comfortable with, there are still a few things you can do to lower that flange and enjoy your new bathroom.

How do you adjust the height of a toilet flange?

Before you can adjust the height of a toilet flange, you need to learn a little bit about the parts that make up a typical toilet flange. A toilet flange sits on top of a floor flange, which is usually made of cast iron. The cast iron flange sits on top of the concrete in the floor of your bathroom, and the toilet flange sits on top of the cast iron flange. A toilet flange is held in place by a set of bolts that are threaded through the flange.  You adjust the height of a toilet flange by changing the height of the toilet flange. Most of the time that means you need to change the height of the floor flange, which in turn changes the Flange — n. 1 : the top of a toilet rim or sink drainpipe 2 : any of a number of thin, flat, circular metal disks used on the outside of a ship’s hull to extend the ship’s lines

Feedback,toilet flange too high this old housetoilet flange extensiontoilet flange 1/8 inch above floortoilet flange spacertoilet flange installationtoilet flange repair kit,People also search for,Privacy settings,How Search works,23:28Toilet Flange Too High | How to Fix Wobbly Toilets, Repair, Install NewjeffostroffYouTube – Nov 15, 2019,23:28,Toilet Flange Too High | How to Fix Wobbly Toilets, Repair, Install New,jeffostroffYouTube – Nov 15, 2019,jeffostroff,YouTube – Nov 15, 2019,4:13How to Install a New Toilet Flange | Ask This Old HouseThis Old HouseYouTube – Aug 27, 2013,4:13,How to Install a New Toilet Flange | Ask This Old House,This Old HouseYouTube – Aug 27, 2013,This Old House,YouTube – Aug 27, 2013,10:06How to Repair a Cast-Iron Toilet Flange | Ask This Old HouseThis Old HouseYouTube – May 27, 2016,10:06,How to Repair a Cast-Iron Toilet Flange | Ask This Old House,This Old HouseYouTube – May 27, 2016,YouTube – May 27, 2016,See more,Oatey 43539 Closet Pvc…,Oatey PVC Twist‑N‑Set Closet Fla…,Oatey Set‑Rite Toilet Flan…,Oatey 43519 Closet Fla…,Oatey 43501 Closet Fla…,Oatey 3 in. PVC Open Offset Toil…,2:57How to Install a Spacer to Fix a Leaking Toilet BowlHome Repair TutorYouTube – Dec 5, 2012,2:57,How to Install a Spacer to Fix a Leaking Toilet Bowl,Home Repair TutorYouTube – Dec 5, 2012,Home Repair Tutor,YouTube – Dec 5, 2012,13:44Set-Rite Toilet Flange 3/4" Spacer , SR-1034RGlobal IndustrialYouTube – Dec 12, 2012,13:44,Set-Rite Toilet Flange 3/4" Spacer , SR-1034R,Global IndustrialYouTube – Dec 12, 2012,Global Industrial,YouTube – Dec 12, 2012,4:47How To Install A Toilet Flange Extension Kit – Master Plumber …The Plumbing GurusYouTube – Feb 22, 2020,4:47,How To Install A Toilet Flange Extension Kit – Master Plumber …,The Plumbing GurusYouTube – Feb 22, 2020,The Plumbing Gurus,YouTube – Feb 22, 2020,maximum height of toilet flange above floor,toilet flange sits too high on concrete floor,toilet flange extension,toilet flange 1/8 inch above floor,toilet flange installation,toilet flange repair kit

You May Also Like

Dumbwaiter Design (Manual, DIY & Elevator Guide)

Here we present our headset design guide, which contains detailed information on…

What are The Various Types of Broadleaf Grass?

Broadleaf grasses are the most common type of lawn grass, and are…

What is Cotton Sateen and What is it Used For?

Cotton sateen is a long-staple cotton fabric woven with a smooth, satiny…

What is Acid Core Soldering and What is it Used For?

When metal parts need to be joined, the most common method is…