If you’ve ever taken a look inside the dorm room of a college senior, you’ve probably noticed that the walls are decorated in a popular style known as board and batten. While the design is quite simple looking, the results are quite striking. The wood panels are the perfect way to upgrade your living space and add a new element of warm and stylish while also maintaining a classic look.
The final step in the home remodeling process is the finishing touches, which include everything from painting the walls to laying down carpet. One of the most frequently overlooked finishing touches is wainscoting, which is the use of thin vertical boards to line the walls (and in some cases the ceiling) of a room.
Board and batten is a term used to describe a wainscot or lath-and-plaster wall treatment, a type of interior wall finish. Wainscot is the term used for a decorative or textured finish, and batten is the term used for the boards that are used to make up the wainscot panel, even if these boards are wood or other materials.
What is a board and batten?
Planks and purlins is the name given to a decorative and sometimes protective architectural detail. It consists of large panels aligned vertically and stacked on top of each other. At the joints between the boards, a thinner board (called a batten) is used to close the joint. Traditionally, boards were made of wood, but today almost any material can be used, including vinyl, aluminum, fiber cement or even steel. As mentioned above, boards and slats were originally used as exterior cladding. The boards were the main protection against the weather, while the purlins prevented air and moisture from entering through the gaps between them. If you use it as a coating, it always works like that. However, as is often the case in architecture, the plank and rule pattern has evolved for use in other environments. Trellis cladding is popular in informal country houses. Shutters with planks and beams are slightly modified when beams are placed diagonally across multiple planks as part of a structural shutter support system.
Are these planks and beams?
It depends on the circumstances. Siding is a protective barrier installed in the lower half or lower third of the room, usually on all walls. The boards and purlins refer to the specific construction that can be used to create this protective barrier. If a pattern of boards and slats is applied to the lower part of the room’s interior, it would be more correct to call it siding. However, planks and purlins are not always used in this way. It is not even always used internally. The plank- and battening can be used for unpainted cladding, such as exterior cladding or blinds. In this case it is not called a covering. You can find more ideas for wall decorations on this page.
What wood is used to make boards?
Although boards and purlins were originally made of wood, they are now available in a variety of materials. The most popular woods for exterior wall cladding are cedar, cypress, mahogany, carob, hemlock and white oak. Non-wood exterior materials include fiber cement, vinyl and steel. Pine or MDF is often used for interior panelling and wainscoting. Slatted boards and finishers are popular materials for DIY walls.
What should be the height of the board and beam scale?
The covering with boards and slats should be in proportion to the total height of the wall. It is usually installed in the lower half or third of the room. The original purpose of wallpaper was to protect the wall from damage. It is often used in dining rooms to protect the wall from bumps and potholes as guests slide chairs backwards. Although it can still be used for this purpose today, most homeowners prefer to install boards and purlins for purely decorative purposes. There is no set rule, so if you want the boards and slats to take up ⅔ or even ¾ of the wall, go for it. It is not recommended to take less than ⅓ of the total wall height. If you are looking for an exact measurement, try 32 inches. The average ceiling height in the living rooms is two meters. The lower third of the wall is covered with a 30 cm thick mantle. Thirty-two inches is also the average height of other upholstery materials, such as. B. Bead panels.
What panel sizes do you use for cladding?
In general, the width of the boards of a siding or panel is one foot. A real lath is no wider than two inches. However, you are free to adjust the dimensions of the boards and purlins to suit your needs. Upholstery is exactly what it sounds like: Instead of placing narrow purlins over the joints of wide boards, the purlins are placed first and the spaces between them are filled with wide boards.
Floor to floor and cladding
From an architectural and historical perspective, cladding is a general term for anything applied to an interior wall to protect it from damage. In interior terminology, it specifically refers to decorative wall detailing that is typically installed in the lower half or lower third of walls. A variation on this decorative detail is the plank and stick pattern. The vertical lines add height to the room and the variation in depth between the boards and purlins adds architectural interest. Wood planks and panels can be painted a different color than the rest of the room to create an accent wall and give the room character. Siding without boards or purlins includes tongue-and-groove, raised or flat panels, tongue-and-groove or beadboard.
What is the difference between boards, planks and beads?
Planks and battens are one of the structures used for cladding. Beading is another option. Both use three-dimensional space and vertical lines to draw the eye upwards and create the illusion of more space above the head. In the first case, narrow planks called purlins are laid on top of other planks to form a three-dimensional structure. In the second example of cladding, the beads, the 3D element comes from semi-circular reliefs (beads) that are pre-milled into the panels before installation. The bead plates are then placed side by side. Cover plates are also available to significantly speed up the installation process without compromising on aesthetics.
Where planks and beams are used
Board and batten siding protects your walls, adds visual interest and dimension, and increases the visibility of vertical space. Its use is not limited to a specific room in the house, so let your imagination run wild.
Boardroom and Knob Dining Room
The dining room is perhaps the most traditional and obvious place for shelves and slats. In large formal dining rooms, chairs are often placed against the wall. In smaller, more intimate dining rooms, guests may accidentally bump into the wall when they slide a chair back to sit or stand. Shelf and slat siding is an attractive and elegant way to prevent unsightly dents and holes in your dining room walls.
board and knob kitchen
The kitchen is different than any other room in the house because most of the walls are invisible. Cabinets and appliances add a lot of visual weight to the bottom half of the room. Board and batten siding can be used in the kitchen if you have large areas of exposed walls. It is generally not recommended to use board and batten siding as a backing board.
Boardroom and Bar
Shelves and purlins are often found in bathroom design and provide a delightful aesthetic. If you use lighter shades in small bathrooms, the shelves and paneling can make the room seem larger than it really is. The boards are generally spaced about 30 cm apart. The top edge of the shelves is usually one third or two thirds of the height of the wall, depending on preference. See more bathroom wall design ideas here.
Wooden battened entrances and passageways
Enclosed spaces where you must fight for freedom of movement often benefit from board and batten siding for two reasons. First, the vertical lines make the space seem larger and less claustrophobic. Secondly, purlins absorb the everyday stresses that occur in a confined space, such as dents, stains and potholes, so your wall remains unaffected. The entrances, covered with planks and slats, create a warm and informal atmosphere. Continuing the design with boards and slats in the hallways of the house is a great way to achieve a country style, even in the middle of the city.
A nursery or playroom is an ideal place to install plank and beam floors. In many parts of the house, you can just install purlins and let the drywall underneath act as a board. When it comes to babies, more protection is a good thing. When things get noisy during playtime and your kids literally crash into the walls, you’ll be thankful for the protective properties of board and batten siding. For other models, see our gallery of skirting styles.There are more than a handful of people who see a board and batten wall as a blank canvas. These people often have a very different vision for the space that they want to have as their home. The space is a blank canvas as it is, so why not make it a wall that you can paint?. Read more about wainscoting vs board and batten and let us know what you think.
Frequently Asked Questions
How do you make wainscoting board and batten?
The style of wainscoting is a common feature in many historic homes. It’s also a popular option for many homeowners, thanks to its versatility and ease of installation. Board and batten wainscoting is a traditional and stylish way to add a nice architectural element to your house or office. It is also known as ‘half wainscoting’ and ‘half batten wainscoting’. This type of wainscoting requires less trimming than full board and batten, making it easier to install. It also has a less pronounced profile than full board and batten wainscoting because the battens are only half the width of a full board and batten board.
What size board do you use for wainscoting?
As with any other home renovation, the process of building a board and batten wainscoting starts with a hole in the wall. A wide board is used for a base, and battens are used to fill in the holes. When you’re ready to start, it’s time to put nail in the board and make sure you have all the materials you’ll need. Our guide walks you through the entire process. From cut boards to paint, we even have a guide to make sure the job is done properly. No matter what size or shape your board, batten, or wainscotting, our article can help you select the correct board size for your project. Our comprehensive guide covers a wide range of board options, including battens and wainscotting.
How far apart should wainscoting panels be?
If you’re looking to finish a room, but don’t know where to start, there’s no need to worry. We’ve done the research for you, and here’s the only wainscoting installation guide you’ll ever need. Wainscoting is a traditional method of dividing wall spaces—usually rooms, hallways, and vestibules—into individual spaces. The term itself comes from the Old English “wain” meaning “a long thin plank” and “scot” meaning “board” or “plank”. This technique of creating wall panels was commonly employed in the Elizabethan era, as well as the Victorian era. The most famous example of this decorative technique is the wainscoting of the “Black Chamber,” a room in the Privy Council Chamber in the Palace of Whitehall in London.
board and batten wall ideaswainscoting layout tipswainscoting trim moldingwainscoting vs board and battenwainscoting dos and don'tsflat panel wainscoting,People also search for,Feedback,Privacy settings,How Search works,board and batten wall ideas,wainscoting layout tips,wainscoting trim molding,wainscoting vs board and batten,wainscoting dos and don'ts,flat panel wainscoting,wainscoting calculator,wainscoting panels